一、電芯老化設備簡介：
1.1 設備功能和原理介紹：設備采用熱風強制對流加熱的方式，每個腔體控制系統相對獨立，以滿足不同時間出入爐需求；每套加熱控制系統采用雙重電子式溫控器控制，以保證控溫精度及可靠的異常超溫保護需求。
1.3 電芯老化總體結構
整機外型尺寸: (大約)長：5050mm；深：2000mm；高：2400mm。
工作室有效內尺寸： 深：1900mm；寬：1000mm；高：1800mm
A, equipment introduction:
1.1 equipment function and the principle is introduced: with the method of hot air forced convection heating, each cavity is relatively independent control system, in order to satisfy the demands of different time of charging; Each heating control system adopts double electronic thermostat control, to ensure that the temperature control precision and reliable abnormal overtemperature protection requirements.
1.3 overall structure
The machine installation dimensions: (approximately) length: 5050 mm; Deep: 2000 mm; Height: 2400 mm.
Studio in the effective size: deep: 1900 mm; Width: 1000 mm; Height: 1800 mm
Second, the equipment can adapt to the processing and product specifications
2.1 per room can be placed two stａnd for a car, at the same time let stａnd for car size: 670 mm wide; 820 mm long; 1660 mm high.
Third, equipment technical parameters
3.1 equipment 40-80 ℃ temperature range.
3.2 equipment temperature control precision is + / - 5 ℃.
3.3 equipment failure rate of 1% or less (caused by equipment failure)
3.4 equipment of furnace chamber under no-load condition from room temperature up to + 80 ℃ is less than 30 minutes.
3.5 equipment within the cavity size: 1000 * 1800 * 1900 (width * * deep).
3.6 electrical equipment: three-phase voltage 380 v, current 120 a, 30 kw power.
3.7 compressed air: 6-8 KGF/cm
3.8 wind pressure and flow rate of 716 pa / 4110 m2 / h
3.9 weight: total weight 580 kg total weight and the ratio of the load bearing area of 500 kg/M2 or less
二、設備能適應的來料和產品規格
2.1每間房可同時放置2個靜置車，靜置車尺寸：寬670mm；長820mm；高1660mm。
三、電芯老化設備技術參數
3.1 設備的恒溫范圍40-80℃。
3.2 設備的溫度控制精度±5℃。
3.3 設備故障率≤1%（指由設備造成的故障）
3.4 設備的爐腔空載狀態下從室溫升到+80℃小于30分鐘。
3.5 設備的內腔尺寸：1000*1800*1900（寬*高*深）。
3.6 設備電氣：電壓三相380V，電流120A， 功率30KW。
3.7 壓縮空氣 ： 6-8kgf/cm
3.8 風壓和流量 716pa/4110m2/h
3.9 重量：總重580Kg 總重與承重面積之比≤500kg/M2
